The effects of polymer concentration and a pore-forming agent (PVP) on HEMA-MMA microcapsule structure and permeability

doi:10.1016/0376-7388(95)00168-9

Journal of Membrane Science

Volume 108, Issue 3, 29 December 1995, Pages 257-268

https://doi.org/10.1016/0376-7388(95)00168-9 Get rights and content

Abstract

The permeability to horseradish peroxidase, (HRP, MW 40 kDa) increased approximately sixty-fold by decreasing the concentration of polymer (HEMA-MMA, hydroxyethyl methacrylate-methyl methacrylate) in triethylene glycol (TEG) from 10 or 11% to 9% (w/v), in microcapsules prepared by interfacial precipitation into phosphate buffered saline. Permeability was determined at the individual capsule level by enzyme-chromogenic substrate assay. With the lower polymer concentration, aggregates and the interconnecting structures formed large interstitial spaces and what appeared to be large pores on the external surface. Adding poly(vinyl pyrrolidone) (PVP) to the HEMA-MMA solution increased the capsule permeability, as much as 25-fold, apparently by increasing the external pore density (defined as the number of pores per unit surface area) without significant deviation in pore size and its distribution. Thus PVP is potentially useful for enhancing the permeability of these capsules which are used to immunoisolate cells used for transplantation. Measurements of molecular weight cut-off are needed before demonstrating that PVP/HEMA-MMA microcapsules are capable of immunoisolating the entrapped cells while maintaining high permeability to the materials essential to encapsulated cell survival and the bioactive cellular products such as insulin.

References (27)

M.V. Sefton et al.
Controlled release using microencapsulated mammalian cells
J. Controlled Release
(1992)
M.J.D. Eenink et al.
Biodegradable hollow fibers for the controlled release of hormones
J. Controlled Release
(1987)
L. Zeman et al.
Characterization of microfiltration membranes by image analysis of electron micrograph. Part I. Method development
J. Membrane Sci.
(1992)
L. Zeman
Characterization of microfiltration membranes by image analysis of electron micrographs. Part II. Functional and morphological parameters
J. Membrane Sci.
(1992)
J.G. Wijmans et al.
Phase separation phenomena in solutions of polysulfone in mixtures of a solvent and a nonsolvent: relationship with membrane formation
Polymer
(1985)
C.A. Smolders et al.
Microstructures in phase-inversion membranes. Part 1. Formation of macrovoid
J. Membrane Sci.
(1992)
A.J. Reuvers et al.
Formation of membranes by means of immersion precipitation. Part I. A model to describe mass transfer during immersion precipitation
J. Membrane Sci.
(1987)
A.J. Reuvers et al.
Formation of membranes by means of immersion precipitation. Part II. The mechanism of formation of membranes prepared from the system cellulose acetate-acetone-water
J. Membrane Sci.
(1987)
M.R. Torres et al.
Comparative study of the behavior of experimental polyamide UF membranes. The effect of polyvinylpyrrolidone used as an additive
J. Membrane Sci.
(1993)
R.M. Boom et al.
Mass transfer and thermodynamics during immersion precipitation for a two-polymer system. Evaluation with the system PES-PVP-NMP-water
J. Membrane Sci.
(1994)

F. Lim et al.

Microencapsulated islets as bioartificial endocrine pancreas

Science

(1980)

G.A. King et al.

Alginate-polylysine microcapsules of controlled molecular weight cut-off for mammalian cell culture engineering

Biotechnol. Prog.

(1987)

C.A. Crooks et al.

Microencapsulation of mammalian cells in a HEMA-MMA copolymer: Effect on capsule morphology and permeability

J. Biomed. Mater. Res.

(1990)

Cited by (35)

Development of high reusability trifunctional polyethersulfones microspheres for the removal of methyl orange
2023, Journal of Water Process Engineering
Citation Excerpt :
Therefore, there was negligible difference in the removal of MO between microspheres synthesized with 10 and 15 wt% PES polymer. Higher PES polymer concentration is usually not recommended for the synthesis of microspheres [43]. Besides being difficult to handle due to high viscosity, high concentration of PES polymer might also lead to the dissipation of positive surface charge on PDDA/Fe3O4 NPs through charge migration [44].
This study focused on the synthesis of trifunctional microspheres with adsorption, degradation, and magnetic responsive properties. Firstly, polyethersulfones (PES) encapsulated poly(diallyldimethyl ammonia) chloride (PDDA) functionalized iron oxide (Fe₃O₄) microspheres were produced via phase inversion method. The PDDA/Fe₃O₄-PES microspheres were further coated with Fe₃O₄ nanoparticles (NPs) on the surface to provide the degradation ability to the formed c-PDDA/Fe₃O₄-PES microspheres. Characterization results such as FTIR analysis confirmed the coating of PDDA on Fe₃O₄ NPs, while the TGA analysis proved the excellent thermal stability of microspheres after the incorporation of PDDA/Fe₃O₄ NPs. BET specific surface area of microspheres was measured at 13.90 m²/g. Besides, the pH drift method confirmed the presence of positive charge on microspheres surface, which is important for the removal of anionic pollutants. Moreover, porous structure of microspheres was also observed under SEM. Formulation study was also carried out to investigate the suitable concentration for the synthesis of microspheres, including the concentration of PES polymer (1–20 wt%), the loading of PDDA/Fe₃O₄ NPs (1–5 wt%), and the concentration of polyethylene glycol (PEG) (1–20 wt%). The microspheres synthesized from different formulations were subjected to the batch removal of methyl orange (MO). Results showed that a 72.53 % removal of MO can be obtained under the following microspheres synthesis formulations: 10wt% of PES polymer, 2 wt% of PDDA/Fe₃O₄ NPs, and 5 wt% of PEG polymer. Lastly, the c-PDDA/Fe₃O₄-PES microspheres also demonstrated an excellent reusability as compared to pure PES microspheres. The c-PDDA/Fe₃O₄-PES microspheres could be reused up to 5 cycles without the need of regeneration while still maintaining high MO removal efficiency.
Fabrication of zeolite NaX-doped electrospun porous fiber membrane for simultaneous ammonium recovery and organic carbon enrichment
2020, Journal of Membrane Science
Citation Excerpt :
To fabricate a stable membrane and further improve the contact efficiency between ammonium and zeolite NaX active sites, the second strategy (Fig. 1, method 2) was attempted to introduce pores on Z-PEFM by dissolving PVP. PVP as one of the most commonly used pore-forming agents can efficiently enhance the mass transfer process [36,37]. By dissolving PVP, the surface of zeolites previously occupied by PVP may be exposed, although the PVDF components on the doped zeolites of Z-EPFM cannot be removed during post-processing.
To achieve ammonium recovery and organic matter enrichment simultaneously, a novel zeolite NaX-doped electrospun porous fiber membrane (Z-EPFM) was fabricated by using the electrospinning technique with the addition of polyvinylidene fluoride (PVDF), zeolite NaX and polyvinylpyrrolidone (PVP) as porogen. The strategy of using PVP as a pore-forming agent to obtain porous Z-EPMFs is more efficient to achieve ammonium adsorption than improving the hydrophilicity of the zeolite NaX-doped electrospun fiber membrane (Z-EFM) by simply adding PVP. As the molecular weight and content of PVP increase, the ammonium adsorption efficiency, hydrophilicity and membrane pore size of Z-EPFMs increase, while their mechanical strength decreases, which is due to the formation of pore structures. The most efficient Z-EPFM (zeolite NaX load density of 0.78 mg/cm²) achieved 96.91% ± 0.50% ammonium adsorption efficiency and 95.48% ± 4.52% organic carbon enrichment efficiency, which were maintained steadily over five regeneration cycles. Therefore, the Z-EPFM offered a novel approach for simultaneous ammonium recovery and organic matter enrichment, which could be proposed as an efficient method to regulate energy flow and control nitrogen nutrient in municipal wastewater.
Gradual PVP leaching from PVDF/PVP blend membranes and its effects on membrane fouling in membrane bioreactors
2019, Separation and Purification Technology
Citation Excerpt :
When additives (such as water, polyethylene glycol, salts, polyvinylpyrrolidone (PVP), etc.) are used, they steer the phase inversion mechanism towards instantaneous demixing and thus result in a more porous membrane structure [7]. PVP is one of the most used additives for membrane fabrication via phase inversion, and is commonly reported as a good pore forming agent [8]. In addition, its presence also increases the viscosity of the casting solution, thus improves commonly applied casting conditions [9].
Improving the hydrodynamics on the membrane surface in a magnetically induced membrane vibration system (MMV) has been proven efficient for membrane fouling control in membrane bioreactors. This advantage can be further extended by using an optimized membrane. This was realized in this study by preparing porous polyvinylidene fluoride membranes via polyvinylpyrrolidone (PVP) blending and later by leaching out the PVP from the membrane matrix via post-treatment using NaOCl. Results show that increasing the PVP content in the casting solution increases membrane fouling resistance. Slowly leaching of PVP after several periodic NaOCl cleanings increased membrane permeance. No advantage of NaOCl post-treatment was observed. The long-term filtration confirmed the superiority of the highly porous membrane that complemented the advantages offered by the MMV system. This suggests that despite the small quantity of the remaining PVP, its leaching offered a substantial gain to improve membrane filterability.
Study on preparation of β-cyclodextrin encapsulation tea extract
2011, International Journal of Biological Macromolecules
Citation Excerpt :
Microcapsules have found numerous applications in various fields, such as pharmaceutical, chemical, textile, biomedical, environmental, petroleum and pesticide industries [6–8]. Common techniques for fabricating hollow microcapsules with dense or porous membranes include interfacial polymerization, in situ polymerization, and interfacial precipitation [6–16]. Tea is the most widely consumed beverage in the world, and its polyphenolic compounds have been found to possess widespread biologic functions and health benefits [17].
Microencapsulation of ethanol extract of tea was performed in this study. In order to microencapsulate, β-cyclodextrin was used as wall material. Ethanol extract of tea was used as the core material. Microcapsules in the solid form were obtained by drying the emulsions. RSM showed that optimal processing parameters were as followings: core material/wall material 1/4, β-cyclodextrin content 16%, stirring time 30 min and stirring temperature 200 °C. Pharmacological activities of β-cyclodextrin encapsulation tea extract were determined. It was found that β-cyclodextrin encapsulation tea extract could enhance BMD, BMC and bone Ca, Zn and Cu contents. In addition, β-cyclodextrin encapsulation tea extract could still reduce blood Ca contents. These results indicated that β-cyclodextrin encapsulation tea extract was useful for improving bone quality in aged animals.
Liquid-liquid two-phase systems for the production of porous hydrogels and hydrogel microspheres for biomedical applications: A tutorial review
2011, Acta Biomaterialia
Citation Excerpt :
Red blood cells were encapsulated in the large microcapsules by co-extrusion in a coaxial geometry. The walls of the microcapsules generally had smooth-surfaced skins with finger-like macrovoids within the walls (Fig. 15) [212,213]. Such structures are typical in membranes formed by immersion precipitation.
Macroporous hydrogels may have direct applications in regenerative medicine as scaffolds to support tissue formation. Hydrogel microspheres may be used as drug-delivery vehicles or as building blocks to assemble modular scaffolds. A variety of techniques exist to produce macroporous hydrogels and hydrogel microspheres. A subset of these relies on liquid–liquid two-phase systems. Within this subset, vastly different types of polymerization processes are found. In this review, the history, terminology and classification of liquid–liquid two-phase polymerization and crosslinking are described. Instructive examples of hydrogel microsphere and macroporous scaffold formation by precipitation/dispersion, emulsion and suspension polymerizations are used to illustrate the nature of these processes. The role of the kinetics of phase separation in determining the morphology of scaffolds and microspheres is also delineated. Brief descriptions of miniemulsion, microemulsion polymerization and ionotropic gelation are also included.
A microfluidic approach to fabricate monodisperse hollow or porous poly(HEMA-MMA) microspheres using single emulsions as templates
2009, Journal of Colloid and Interface Science
We have successfully developed a novel and simple method to controllably prepare monodisperse poly(hydroxyethyl methacrylate–methyl methacrylate) (poly(HEMA–MMA)) microspheres with two distinct structures using single emulsions as templates. By employing a microfluidic emulsification approach to fabricate monomer-contained oil-in-water (O/W) emulsions as templates, and introducing proper initiators and different types of porogens, poly(HEMA–MMA) microspheres with hollow or porous structure are prepared in a controllable way. The shell thickness of hollow microspheres or the porosity of porous microspheres is controllably achieved by simply adjusting the porogen concentration. The prepared poly(HEMA–MMA) microspheres with controllable hollow or porous structures are favored for various potential applications. Furthermore, by using the simple preparation methodology proposed in this study, fabrication of monodisperse porous microspheres or hollow microcapsules with other materials can also be easily achieved.

View all citing articles on Scopus

View full text

The effects of polymer concentration and a pore-forming agent (PVP) on HEMA-MMA microcapsule structure and permeability

Abstract

J. Controlled Release

J. Controlled Release

J. Membrane Sci.

J. Membrane Sci.

Polymer

J. Membrane Sci.

J. Membrane Sci.

J. Membrane Sci.

J. Membrane Sci.

J. Membrane Sci.

Microencapsulated islets as bioartificial endocrine pancreas

Science

Alginate-polylysine microcapsules of controlled molecular weight cut-off for mammalian cell culture engineering

Biotechnol. Prog.

Microencapsulation of mammalian cells in a HEMA-MMA copolymer: Effect on capsule morphology and permeability

J. Biomed. Mater. Res.